Skip To Main Content

Leaving our website

You are about to view content that is outside the control of Roseville Joint Union High School District. The district is not responsible for its accuracy or appropriateness.

Logo Image

Eppendorf 5402 Manual 'link'

The Eppendorf 5402 is designed for sedimentation of small volumes in microcentrifuge tubes (typically 0.5 mL to 2.0 mL). Key Performance Specifications 14,000 revolutions per minute (rpm). Maximum RCF: 16,000 × g (relative centrifugal force). Temperature Range: -9°C to +40°C.

1 to 99 minutes, or continuous operation ("Hold").

The 5402 model features intuitive controls for speed, time, and temperature. Loading the Rotor eppendorf 5402 manual

Before operating the Eppendorf 5402, you must understand its mechanical and electrical limitations to ensure safe and efficient operation. Feature / Parameter Specification Detail 14,000 Rotations Per Minute (RPM) Maximum Relative Centrifugal Force (RCF) 16,000 × g Temperature Control Range -9°C to +40°C Standard Rotor Capacity 18 x 1.5 mL / 2.0 mL microcentrifuge tubes Timer Range 1 to 99 minutes, plus a continuous run option ("Hold") Power Requirements 120V (60 Hz) or 230V (50-60 Hz) depending on regional model Refrigerant Type CFC-free cooling system 2. Installation and Initial Laboratory Setup

. The "legendary" part of its manual (and its function) is the feature. In just 10 minutes , the 5402 can drop from room temperature to a crisp The Eppendorf 5402 is designed for sedimentation of

| Error Code | Description | Recommended Solution(s) | | :--- | :--- | :--- | | | Rotor not recognized, or power issue | Reinstall rotor correctly. Check power connections. | | Error 3 / E3 | Incorrect speed measurement or temperature control | Check sensor connection. Verify cooling system settings. | | Error 4 / E4 | Lid lock sensor failure or rotor imbalance | Inspect lid lock and balance sample load. | | Error 5 / E5 | Lid switch damaged or over-speed warning | Inspect lid switch. Lower speed setting if too high. | | Error 6 / E6 | Low voltage | Check power supply voltage and circuit connections. | | Error 7 / E7 | Overspeed or temperature sensor failure | Reduce speed setting. Check sensor connection. | | Error 8 / E8 | Drive/motor error or control panel fault | Check for overheating. Try restarting device. |

The following article provides a technical overview and operating guidelines for the Eppendorf Centrifuge 5402 Temperature Range: -9°C to +40°C

To help troubleshoot a specific problem with your unit, let me know: What or symptom are you seeing? The rotor model you are using

Logo Title

The Eppendorf 5402 is designed for sedimentation of small volumes in microcentrifuge tubes (typically 0.5 mL to 2.0 mL). Key Performance Specifications 14,000 revolutions per minute (rpm). Maximum RCF: 16,000 × g (relative centrifugal force). Temperature Range: -9°C to +40°C.

1 to 99 minutes, or continuous operation ("Hold").

The 5402 model features intuitive controls for speed, time, and temperature. Loading the Rotor

Before operating the Eppendorf 5402, you must understand its mechanical and electrical limitations to ensure safe and efficient operation. Feature / Parameter Specification Detail 14,000 Rotations Per Minute (RPM) Maximum Relative Centrifugal Force (RCF) 16,000 × g Temperature Control Range -9°C to +40°C Standard Rotor Capacity 18 x 1.5 mL / 2.0 mL microcentrifuge tubes Timer Range 1 to 99 minutes, plus a continuous run option ("Hold") Power Requirements 120V (60 Hz) or 230V (50-60 Hz) depending on regional model Refrigerant Type CFC-free cooling system 2. Installation and Initial Laboratory Setup

. The "legendary" part of its manual (and its function) is the feature. In just 10 minutes , the 5402 can drop from room temperature to a crisp

| Error Code | Description | Recommended Solution(s) | | :--- | :--- | :--- | | | Rotor not recognized, or power issue | Reinstall rotor correctly. Check power connections. | | Error 3 / E3 | Incorrect speed measurement or temperature control | Check sensor connection. Verify cooling system settings. | | Error 4 / E4 | Lid lock sensor failure or rotor imbalance | Inspect lid lock and balance sample load. | | Error 5 / E5 | Lid switch damaged or over-speed warning | Inspect lid switch. Lower speed setting if too high. | | Error 6 / E6 | Low voltage | Check power supply voltage and circuit connections. | | Error 7 / E7 | Overspeed or temperature sensor failure | Reduce speed setting. Check sensor connection. | | Error 8 / E8 | Drive/motor error or control panel fault | Check for overheating. Try restarting device. |

The following article provides a technical overview and operating guidelines for the Eppendorf Centrifuge 5402

To help troubleshoot a specific problem with your unit, let me know: What or symptom are you seeing? The rotor model you are using